Customize Eagle – Icons

Drill sets the drilling speed. You may remember that I do not recommend using the Milling option unless you have no other way to cut your final PCB down to size. If you need to use this option, go very slow because it will put a lot of stress on your end mill. Though I have not used it, this would probably work well with the same settings as Etch. Un-checking all of the NC File Comments options will fix this issue.
cadsoft eagle 7

CadSoft EAGLE 7.5.0 Lock Bug Fix

Drill sets the drilling speed. You may remember that I do not recommend using the Milling option unless you have no other way to cut your final PCB down to size. If you need to use this option, go very slow because it will put a lot of stress on your end mill. Though I have not used it, this would probably work well with the same settings as Etch. Un-checking all of the NC File Comments options will fix this issue. Unfortunately, the G-Code file for drilling still gives me an error due to a long notation at the top of the file.

This is easy to fix and we will go over that in the Troubleshooting section. Under Other Options, I only check the Do tool change with zero step and Use simple drill code options. File Naming can be changed if you really want to, but I would just leave it alone. If you are using an end mill with a 0. This gets a little tricky when you are dealing with an engraving bit, because the cut widens as it goes deeper, but I would not worry about it unless you need a fine pitch.

Soon I will try to do a 0. Click the Clearance tab. To ensure that all of your traces get isolated, change all of the values to the diameter of your milling bit. For example; I use an engraving bit that cuts at about 0. See Figure 4 Now click the Apply button. Click the Check button to look of DRC errors. If you have any errors, they will show in the DRC window.

Double click an error from the list to show you where it occurs in your design. There are two ways that you can design your PCB for a single sided board. You can design your traces from the top or from the bottom. Most of this depends on how you want to mount your components. Through-hole components are easier to solder on if you put them on the non copper side so that the pins stick out through the copper.

PCB with Bottom wires. This is where you may have to think a bit about your design. So if you are using through-hole components, you may want to do all of your wire connections using Bottom wires. Also be sure that you mirror any text that you want etched as well so that is shows up in the right place. When done, click Accept and make my board.

A preview of the trace outline will display. Type the letter C to see the outlines more clearly. Inspect the preview to be sure that everything looks good. Type the letter Q to close the window. Click the OK button on the popup window to see the next preview. Generate Outlines and Generate drills show up on the same preview. This is the point where the CNC Mill will start at. This works out perfect if you designed your PCB with all Top wires.

However, the point of origin is moved to the bottom right corner if your PCB was designed with Bottom wires. Though this will work, if you really need to start in the lower left, there is a way to know how far over you will need to move for the new point of origin.

This is known as a registration mark. The registration mark shows you where the point of origin is and the two sets of red numbers tells you the exact distance that mark is from point 0. You may notice that in figure 5, the registration marks are on opposite sides and the numbers are not the same. We will go over this again in a tutorial about setting your CNC Mill up and running the code. For this type of board, I would recommend adding a set of holes that can be used to align the board properly when it is turned over.

Just be sure that the holes you drill will be in the same place even when the PCB is flipped. I suggest placing these holes on all 4 corners of the PCB. Troubleshooting G-Code Errors The most common error that you will encounter has to do with long comments that appear at the beginning of the Drill files.

This error is easy to fix with the help of a text editor. Locate and open the your file name. You can remove all of the comments from this file, but the long comment on line 4 is the most likely one to give you trouble. Save and close the file. All of the other files will run smoothly. However I would suggest, if you understand G-Code, that the following code be added just after the last Z movement.

G00 Z1. You can also add G21 to the very end to switch back from Inches to MM the software default For more about G-Code, have a look at these resources:

Publisher Description

Sujet du message: Mar 19 Avr The combination of those two things means I can’t duplicate the setup Icurrently have, so this is the classic example of how proprietarysoftware owners can screw you over without you having any recompense orworkaround, despite you being a paying and loyal customer for anextended period of time. Whether a library file is in use or not can be checked quickly in the Tree Views Libraries branch. Select the MOVE command, hold the Ctrl key pressed, and click onto an object in order to bring its origin point into the currently active grid. This group is mainly kept in English. In the Download areasLibrariesdirectory are lots of user-contributed files available for free download.

VIDEO: CadSoft Enhances PCB Design Software

EAGLE VERSION 7. Schematic. Layout. Autorouter. Sales/Support Americas +1 , Sales@dkey.finnflare.ru, Support@dkey.finnflare.ru CadSoft EAGLE recently released an update to their PCB design suite that brings Familiarize Yourself with These 7 Dev Board Features. This software and documentation are copyrighted by CadSoft Computer, doing the computers running Windows 7 as well, copy the files dkey.finnflare.ru and.

Leave a Reply

Your email address will not be published. Required fields are marked *